How Long Should the Immersion Be On? Immersion Cost Calculator

Immersion cost calculator

Last updated 17 November 2026, using Electric Ireland's current standard rates.

To reheat a typical day's hot water, about half a 120 litre tank, the immersion only needs to be on for about 1 hour 7 minutes, so a timer set for an hour and a half covers it. A 3kW immersion heats a full 120 litre tank from cold in about 2 hours 14 minutes, for about €2.55 at 38.04c a unit or €1.34 on night rate. Leaving it on all the time is not cheaper: it keeps paying to replace heat that leaks out of the tank.

Work out your cost  ·  Leave it on or not?  ·  Set your timer

Immersion cost calculator

Set your tank, how much hot water you use and your tariff. The size is usually on a label on the cylinder; 120 litres is a common size.

1 hour 30 minutestimer a day for your use
€1.27a day
€38.73a month
2 hours 14 minutesto heat a full tank from cold

Heating a full tank from cold uses 6.7 units and costs €2.55. On night rate your hot water would cost about €20.39 a month instead of €38.73. Leaving the immersion on around the clock adds up to €13.88 a month for heat that leaks out of the tank.

Heating water takes 4.186 kJ per litre per °C. Heat lost from the tank is an estimate: about 1.2 units a day for a 120 litre foam insulated cylinder, about double with a lagging jacket. Rates are Electric Ireland standard rates from 1 July 2026, including VAT, before any discount; check your bill and use your own.

Is it cheaper to leave the immersion on all the time?

No. The thermostat switches the element off when the water reaches temperature, but heat leaks out of the cylinder all day and night, and the element keeps switching back on to replace it. You pay for that whether or not anyone uses the water.

For a modern 120 litre cylinder with factory foam insulation that is about 1.2 units a day, up to €13.88 a month. With a lagging jacket it is roughly double, up to €27.75 a month. A timer that heats the water shortly before you need it saves a good part of that, because the tank is not held hot through the hours nobody is using it.

How long should the immersion be on?

Long enough to reheat what you used. With a standard 3kW element:

  • ✓A full 120 litre tank from cold takes about 2 hours 14 minutes.
  • ✓Reheating half the tank, a typical day's use, takes about 1 hour 7 minutes.
  • ✓The sink setting on a dual immersion heats only the top of the tank with the top element, so it is quicker for a small amount of hot water.

How long an immersion takes to heat a tank

From 12°C to 60°C with a standard 3kW element, at the 38.04c 24 hour rate.

Tank Full tank from cold Units Cost Cost on night rate
90 litres 1 hour 40 minutes 5.0 €1.91 €1.01
120 litres 2 hours 14 minutes 6.7 €2.55 €1.34
150 litres 2 hours 47 minutes 8.4 €3.18 €1.68
200 litres 3 hours 43 minutes 11.2 €4.25 €2.24

Topping up after a normal day's use takes less, because the tank is still partly hot.

How to set your immersion timer

  1. Work out how long you need from the calculator above, rounded up to the next half hour.
  2. On a day and night meter, set that time inside the night hours, usually 11pm to 8am, so the tank is hot by morning.
  3. On the 24 hour rate, set it to finish shortly before you most need hot water, for example an hour before the evening.
  4. Use the boost button for an extra top up instead of switching the immersion to constant.
  5. Set the thermostat to about 60°C. Legionella bacteria are killed within a few minutes above 60°C, so do not set it lower to save money.

Never run an immersion through a plug in timer or smart plug. A 3kW immersion is a fixed appliance on its own circuit, and an immersion timer is wired in by a registered electrician.

Immersion timers

Free delivery from the first euro, anywhere in Ireland. See all immersion timers and heating controls. For heaters, see what an electric radiator costs to run, and for everything else use our electricity cost calculator.

Questions

How long should the immersion be on?

Long enough to reheat the water you use. Reheating half of a 120 litre tank takes a 3kW element about 1 hour 7 minutes, so a timer set for an hour and a half covers a typical day. Heating a full 120 litre tank from cold to 60°C takes about 2 hours 14 minutes. The calculator on this page works it out for your tank and use.

Is it cheaper to leave the immersion on all the time?

No. The thermostat stops it boiling, but it keeps topping up heat that leaks out of the tank all day and night. For a modern foam insulated 120 litre cylinder that is about 1.2 units a day, up to €13.88 a month at 38.04c, and roughly double with a lagging jacket. A timer that heats the water before you need it, ideally on night rate, saves a good part of that.

How much does it cost to run an immersion in Ireland?

A standard 3kW immersion uses 3 units an hour while it is heating: about €1.14 an hour at the 38.04c 24 hour rate, or 60 cent an hour at the 20.03c night rate. Heating half of a 120 litre tank each day costs about €38.73 a month on the 24 hour rate, or €20.39 on night rate.

How long does an immersion take to heat a tank?

About 2 hours 14 minutes for a 120 litre tank from cold to 60°C with a 3kW element, and about 2 hours 47 minutes for a 150 litre tank. Topping up a partly hot tank takes less.

What temperature should the immersion be set to?

Around 60°C. Legionella bacteria are killed within a few minutes above 60°C, according to the Health Protection Surveillance Centre, so a lower setting is not worth the small saving. Water at that temperature can scald, so take care at the tap.

Is it cheaper to heat water on night rate?

Yes, if you have a day and night meter or a smart tariff. Electric Ireland's NightSaver night rate is 20.03c per unit against 40.62c by day (standard rates including VAT from 1 July 2026), so the same tank costs about half. Set the timer inside the cheap hours, usually 11pm to 8am, and use the boost for a top up during the day.

Can I put a timer on my immersion?

Yes. An immersion timer or boost timer is wired into the immersion circuit by a registered electrician. Never run an immersion through a plug in timer or smart plug: a 3kW immersion is a fixed appliance on its own circuit.

Rates are Electric Ireland standard rates from 1 July 2026, including VAT, before any discount. Heat loss figures are estimates and your tank, pipework and use will differ. Last updated 17 November 2026. Questions? Call 01 401 9907 or email sales@shamrockelectrical.ie.